乐泰C-200是做什么用的？那里能买到？loctite C-200胶水里面的成份

乐泰C-200是做什么用的？那里能买到？loctite C-200胶水里面的成份：

本文来自：汉高乐泰胶水（中国）有限公司 Henkel Loctite官网 www.loctite.net/c1294.html 

乐泰loctite C-200防卡剂，主要应用于铁车轨道，机械，防止产品不生锈不腐蚀，容易后期维护拆除。

以下是产品的主要成份及参数：

  Product Description Sheet

    LOCTITE® FREKOTE C-200 & C-210

    Known as

    Frekote Aqualine C-200 & C-210®

    September 2015

Description     Application *Consult MSDS Prior to Use**Loctite Frekote C-200 is a unique water based release agent®    ®

designed to provide multiple release with no contaminating     Loctite Frekote  C-200 and C-210 are designed to be applied®    ®

transfer. Loctite Frekote C-200 can be applied to molds at ®    ®    to molds at any temperature between 20°C (68°F) and 205°Cany  temperature  between  room  temperature  and  205°C     (400°F). (Loctite Frekote  C-210 is to be used as a touch-up®    ®

(400°F). Loctite Frekote C-200 chemically bonds to the mold ®    ®    coat only and as such, should be applied over an Loctite®surface to form a thin, chemically resistant coating capable of     Frekote C-200 base coat.) Spray application is recommended,®

releasing all thermoset composites. Aqualine C-200 is a water     although brush, wipe or dip techniques may be used. Optimumbased product which contains no CFC's and no chlorinated,     multiple release performance is obtained by applying to moldsaromatic or petroleum based solvents thus making it one of the     preheated to between 40°C (104°F) and 100°C (212°F). Thesafest, non-flammable, very low VOC products available. When     ease of release, number of releases/application and surfaceused according to directions, Loctite Frekote C-200 gives no ®    ®    finish will depend on application technique, mold temperaturemold build-up and exhibits high thermal stability for all molding     and number of coats applied.

processes.

    1.  When applying Loctite Frekote C-200 to a mold at room®    ®

    temperature (approximately 20°C/68°F), use a minimum ofLoctite Frekote C-210 is designed for applications where a ®    ®    six coats. Allow each coat to dry (approximately 10hot >60°C, (140°F) mold touch-up is required or where spray     minutes) before applying the subsequent coat. The dryapplication is  being  utilized.  Loctite ® Frekote ® C-210 is     time may be decreased, by using a fan or infrared lamps.recommended for use over a Loctite Frekote C-200 base ®    ®    Post cure the final film for at least 40 minutes at 60°Ccoat. As with the C-200, Loctite Frekote C-210 provides ®    ®    (140°F). 20 minutes at 100°C (212°F) or 15 minutes atmultiple release and no contaminating transfer     120°C (250°F) prior to starting production

Features    2.  Care should be taken to avoid emulsion accumulation andNo Contaminating Transfer     running due to over application. If spray application is to beReduced reject rate     used, low pressure, high volume spray equipment (HVLP)Very low VOC content     is recommended to produce optimum transfer efficiencySupplied ready to use; no mixing required     and reduce over-spray. Porous molds should be preheatedNon-flammable     to a minimum of 60°C (140°F) prior to release agentNo CFC's, chlorinated or aromatic solvents     application.

Multiple releases per application

Virtually no mold build-up      3.  When applying Loctite Frekote C-200 to molds above®    ®

Non-irritating     room temperature (>40°C;104°F), apply a minimum of four

    coats. Again, allow each to dry before applying the

    subsequent coat. At 60°C (140°F), C-200 will dry in a fewProperties     seconds; above 100°C (212°F) it will dry instantaneously.Appearance     White emulsion     Allow 40 minutes at 60°C (140°F), 20 minutes at 100°COdor     Slight mild odor     (212°F) or 15 minutes at 120°C (250°F) for the final film toSpecific Gravity     C-200: 0.99     cure prior to production.

    C-210: 1.00

Special Cautions      Store below 40°C (104°F)

Cured thermal stability        600F (315ºC)    Touch-up

    The frequency of touch-up will depend on polymer type, mold

    configuration and abrasion parameters. Touch up with Loctite®

    Frekote C-200 only to areas where poor release is noticed. If®

Mold Preparation    spray applying to a hot mold >60°C, (140°F), or if release agentMold surfaces must be thoroughly cleaned and dried. All traces

of prior release agents and contaminants must be removed.     build-up is a concern, touch-up with Loctite Frekote C-210.®    ®This may be accomplished by using Loctite Frekote PMC, PMC    Again, allow the touch-up coat to cure, for the minimum timePlus or other suitable solvents. Heavy build-up will probably    given above, prior to commencing production.

require abrasion (e.g., grit sand or glass beading) followed by

solvent washing. This will remove polymer buildup or previous

release contamination.

    Product Description Sheet

    LOCTITE® FREKOTE C-200 & C-210

    Known as

    Frekote Aqualine C-200 & C-210®

    September 2015

Note    recommend that you carry out your own prior trials to confirm suchThe information provided in this Technical Data Sheet (TDS) including    suitability of our product.

the recommendations for use and application of the product are based

on our knowledge and experience of the product as at the date of this    Any liability in respect of the information in the Technical Data Sheet orTDS. The product can have a variety of different applications as well as    any other written or oral recommendation(s) regarding the concerneddiffering application and working conditions in your environment that are    product is excluded, except if otherwise explicitly agreed and except inbeyond our control. Henkel is, therefore, not liable for the suitability of    relation to death or personal injury caused by our negligence and anyour product for the production processes and conditions in respect of    liability under any applicable mandatory product liability law.which you use them, as well as the intended applications and results.

We strongly recommend that you carry out your own prior trials to    Trademark usage

confirm such suitability of our product.    Except as otherwise noted, all trademarks in this document areAny liability in respect of the information in the Technical Data Sheet or    trademarks of Henkel Corporation in the U.S. and elsewhere. ®any other written or oral recommendation(s) regarding the concerned    denotes a trademark registered in the U.S. Patent and Trademarkproduct is excluded, except if otherwise explicitly agreed and except in    Office.

relation to death or personal injury caused by our negligence and any

liability under any applicable mandatory product liability law.

In case products are delivered by Henkel Corporation, Resin

Technology Group, Inc., or Henkel Canada, Inc.the following disclaimer

is applicable:

The data contained herein are furnished for information only and are

believed to be reliable. We cannot assume responsibility for the results

obtained by others over whose methods we have no control. It is the

user's responsibility to determine suitability for the user's purpose of

any production methods mentioned herein  and to adopt such

precautions as may be advisable for the protection of property and of

persons against any hazards that may be involved in the handling and

use thereof. In light of the foregoing, Henkel Corporation specifically

disclaims all warranties expressed or implied, including warranties

of merchantability or fitness for a particular purpose, arising from

sale or use of Henkel Corporation’s products. Henkel Corporation

specifically disclaims any liability for consequential or incidental

damages of any kind, including lost profits. The discussion herein of

various processes or compositions is not to be interpreted as

representation that they are free from domination of patents owned by

others or as a license under any Henkel Corporation patents that may

cover such processes or compositions. We recommend that each

prospective user test his proposed application before repetitive

use, using this data as a guide. This product may be covered by one or

more United States or foreign patents or patent applications.

In case products are delivered by Henkel Belgium NV, Henkel

Electronic Materials NV, Henkel Nederland BV, Henkel Technologies

France SAS and Henkel France SA please additionally note the

following:

In case Henkel would be nevertheless held liable, on whatever legal

ground, Henkel’s liability will in no event exceed the amount of the

concerned delivery.

In case products are delivered by Henkel Colombiana, S.A.S. the

following disclaimer is applicable:

The information provided in this Technical Data Sheet (TDS) including

the recommendations for use and application of the product are based

on our knowledge and experience of the product as at the date of this

TDS. Henkel is not liable for the suitability of our product for the

production processes and conditions in respect of which you use them,

as well as the intended applications and results. We strongly

上一页：乐泰胶水LOCTITE ABLESTIK 2115